Product Details:
Minimum Order Quantity | 1 Piece |
Brand | ResMed |
Model | AURCURVE 10 VAUTO |
Pressure Range (cm H2O) | 4-25 |
Operating Mode | VAUTO |
Type | Auto BiPAP |
Warranty | 2 YEARS |
Weight | 1 KGS. |
Dimensions | 159 mm x 66 mm x 72 mm |
Data Storage Capacity | ONLINE STORAGE, SD CARD |
Brand | ResMed |
Model | AirCurve 10 Vauto |
Usage/Application | Hospitals & Personal Use |
Pressure Range (cm H2O) | S, VAuto: 2 to 25 cm H2O (2 to 25 hPa); CPAP: 4 to 20 cm H2O (4 to 20 hPa) |
Ramp Rate (mins) | 5 to 45 minutes |
Pressure Sensor | Internally located at device outlet, analogue gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa) |
Power Supply Unit | 90 W, AC input range:100–240 V, 50–60 Hz 1.0–1.5 A, Class II 115 V, 400 Hz 1.5 A, Class II (nominal for aircraft use); DC output:24 V 3.75 A |
Flow Sensor | Internally located at device inlet, digital mass flow type, -70 to +180 L/min |
Weight With Humidifier | 1248 gm |
Dimensions | 205 x 150 x 116 mm (without humidifier), 255 x 150 x 116 gm (with humidifier) |
Warranty | 2 Years |
Operating Temperature | +5°C to +35°C Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (40°C) the device remains safe. |
Operating Altitude | Sea level to 2591 m; air pressure range 1013 hPa to 738 hPa |
Pressure Level Measured | According to EN ISO 17510-1:2009 (CPAP mode); SlimLine: 26.6 dBA with uncertainty of 2 dBA, Standard: 26.6 dBA with uncertainty of 2 dBA |
Power Level Measured | According to EN ISO 17510-1:2009 (CPAP mode); SlimLine: 34.6 dBA with uncertainty of 2 dBA, Standard: 34.6 dBA with uncertainty of 2 dBA |
Operating Mode | S, VAuto, CPAP |
Housing Construction | Flame retardant engineering thermoplastic |
Supplemental Oxygen | Maximum flow: 15 L/min (CPAP, S); 4 L/min (VAuto) |
Standard Air Filter | Material: Polyester non woven fibre, Average arrestance: >75% for -7 micron dust |
Hypoallergenic Air Filter | Material: Acrylic and polypropylene fibres in a polypropylene carrier, Efficiency: >98% for:- 7-8 micron dust; >80% for:- 0.5 micron dust |
Air Outlet | 22 mm |
Water Capacity | To maximum fill line 380 mL |
Typical Power Consumption | 53 W (57 VA) |
Peak Power Consumption | 104 W (108 VA) |
Maximum Single Fault Steady Pressure | Device will shut down in the presence of a single fault if the steady state pressure exceeds:30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec |
Wireless Module | Technology used:4G, 2G. It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories. Technology may not be available in all regions |
Design Life | Device, power supply unit - 5 years / Cleanable humidifier - 2.5 years / Air tubing - 6 months |
Operating Humidity | 10 - 95% relative humidity, non-condensing |
Storage and Transport Temperature | -20°C to +60°C |
Storage and Transport Humidity | 5 - 95% relative humidity, non-condensing |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | ResMed |
Model | AIRCURVE 10 ST |
Pressure Range (cm H2O) | 4-25 |
Operating Mode | S-ST |
Ramp Rate | 0-45 |
Type | BiPAP |
Warranty | 2 YEARS |
Weight | 1 KGS. |
Dimensions | 159 mm x 66 mm x 72 mm |
Data Storage Capacity | ONLINE STORAGE,SD CARD |
Product Details
Brand | ResMed |
Model | AirCurve 10 Vauto |
Usage/Application | Hospitals & Personal Use |
Pressure Range (cm H2O) | S, VAuto: 2 to 25 cm H2O (2 to 25 hPa); CPAP: 4 to 20 cm H2O (4 to 20 hPa) |
Ramp Rate (mins) | 5 to 45 minutes |
Additional Details
Pressure Sensor | Internally located at device outlet, analogue gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa) |
Power Supply Unit | 90 W, AC input range:100–240 V, 50–60 Hz 1.0–1.5 A, Class II 115 V, 400 Hz 1.5 A, Class II (nominal for aircraft use); DC output:24 V 3.75 A |
Flow Sensor | Internally located at device inlet, digital mass flow type, -70 to +180 L/min |
General System
Weight With Humidifier | 1248 gm |
Dimensions | 205 x 150 x 116 mm (without humidifier), 255 x 150 x 116 gm (with humidifier) |
Warranty | 2 Years |
Comfort Features
Operating Temperature | +5°C to +35°C Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (40°C) the device remains safe. |
Operating Altitude | Sea level to 2591 m; air pressure range 1013 hPa to 738 hPa |
Sound
Pressure Level Measured | According to EN ISO 17510-1:2009 (CPAP mode); SlimLine: 26.6 dBA with uncertainty of 2 dBA, Standard: 26.6 dBA with uncertainty of 2 dBA |
Power Level Measured | According to EN ISO 17510-1:2009 (CPAP mode); SlimLine: 34.6 dBA with uncertainty of 2 dBA, Standard: 34.6 dBA with uncertainty of 2 dBA |
Additional Details
Operating Mode | S, VAuto, CPAP |
Housing Construction | Flame retardant engineering thermoplastic |
Supplemental Oxygen | Maximum flow: 15 L/min (CPAP, S); 4 L/min (VAuto) |
Standard Air Filter | Material: Polyester non woven fibre, Average arrestance: >75% for -7 micron dust |
Hypoallergenic Air Filter | Material: Acrylic and polypropylene fibres in a polypropylene carrier, Efficiency: >98% for:- 7-8 micron dust; >80% for:- 0.5 micron dust |
Air Outlet | 22 mm |
Water Capacity | To maximum fill line 380 mL |
Typical Power Consumption | 53 W (57 VA) |
Peak Power Consumption | 104 W (108 VA) |
Maximum Single Fault Steady Pressure | Device will shut down in the presence of a single fault if the steady state pressure exceeds:30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec |
Wireless Module | Technology used:4G, 2G. It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories. Technology may not be available in all regions |
Additional Details
Design Life | Device, power supply unit - 5 years / Cleanable humidifier - 2.5 years / Air tubing - 6 months |
Operating Humidity | 10 - 95% relative humidity, non-condensing |
Storage and Transport Temperature | -20°C to +60°C |
Storage and Transport Humidity | 5 - 95% relative humidity, non-condensing |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | ResMed |
Model | LUMIS 150 ST WITH IVAPS |
Pressure Range (cm H2O) | 4-25 |
Operating Mode | S, ST, T, IVAPS |
Ramp Rate | 0-45 |
Type | BiPAP |
Warranty | 2 YEARS |
Weight | 1 KGS. |
Dimensions | 159 mm x 66 mm x 72 mm |
Data Storage Capacity | ONLINE STORAGE, SD CARD |
Brand | ResMed |
Model | Lumis 150 |
Usage/Application | Hospitals & Personal Use |
Pressure Range (cm H2O) | 2–25 cm H2O (2–25 hPa) in S, T, ST, PAC and iVAPS modes, 4–20 cm H2O (4–20 hPa) in CPAP mode |
Sound/Noise Level (db) | 26.6 dBA with uncertainty of 2 dBA as measured according to ISO 17510-1:2009 (CPAP mode) |
Dimensions | 116 mm x 205 mm x 150 mm (Device only), 116 mm x 255 mm x 150 mm (Device with HumidAir humidifier) |
Weight Without Humidifier | 1106 g |
Weight With Humidifier | 1268 g |
Operating Temperature | +5°C to +35°C |
Operating Altitude | Sea level to 2,591 m, Air pressure range 1013 hPa to 738 hPa |
Operating Mode | CPAP, S, T, ST with optional iBR, PAC, iVAPS with iBR and optional AutoEPAP |
90 W Power Supply Unit | Input range: 100–240 V, 50-60 Hz, 57 VA (typical power consumption) 108 VA (peak power consumption) |
Housing Construction | Flame retardant engineering thermoplastic |
Supplemental Oxygen | Recommended maximum flow: 15 L/min (CPAP, S, T, ST, PAC); 4 L/min (iVAPS) |
Standard Air Filter | Polyester non-woven fibre |
Tubing | SlimLine and ClimateLineAir (15 mm); Standard (19 mm) |
Air Outlet | 22 mm air outlet complies with ISO 5356-1:2004 |
Classification | IEC 60601-1: 2006: Class II (double insulation), Type BF Ingress protection IP22 |
Operating Humidity | 10–95% relative humidity, non-condensing |
Storage and Transport Temperature | -20°C to +60°C |
Storage and Transport Humidity | 5–95% relative humidity, non-condensing |
Lumis 150 VPAP ST is a non invasive ventilator designed for non-dependent patients with obstructive or restrictive respiratory conditions.
Featuring ResMed’s unique volume-assurance mode – iVAPS (intelligent Volume-Assured Pressure Support) – Lumis 150 VPAP ST maintains target alveolar ventilation to suit each patient’s changing needs. And with an intelligent Backup Rate (iBR) and optional AutoEPAP, iVAPS continuously monitors ventilation and the upper airway.
The ventilator is easy to set up and use, and is supported by ResMed’s ResScan patient management software.
TiControl lets you set min and max limits on either side of the patient’s ideal inspiratory time to encourage spontaneous breathing
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | ResMed |
Model | LUMIS 100 |
Pressure Range (cm H2O) | 4-25 |
Operating Mode | S, CPAP |
Ramp Rate | 0-45 |
Type | BiPAP |
Warranty | 2 YEARS |
Weight | 1 KGS. |
Dimensions | 159 mm x 66 mm x 72 mm |
Data Storage Capacity | ONLINE STORAGE, SD CARD |
Application | Hospital, Clinical Purpose |
Modes | S |
Pressure Range | IPAP 4 - 25 cm H2O |
Breath Rate | 0 - 30 beats per min |
Ramp Time | 0-45 mins |
Power Requirements | 240 V |
Filters | Foam |
Electrical Requirement | 240 V |
Portable | Yes |
Warranty | 24 months |
Color | Black, Grey |
Condition | New |
ResMed Lumis 100 VPAP S
Lumis 100 VPAP S is a noninvasive ventilator designed for spontaneously breathing, non-dependent patients with respiratory insufficiency with personalized ventilation made easy.
The ventilator is easy to set up and use, and is supported by ResMed’s ResScan™ patient management software.
Key features
Warranty & Services:
Additional Information: